PI Interfaces

Showing 304 of 4879

Test Modbus Serial interface with newer Operating Systems

Currently the Modbus Serial interface supports Windows 7 as the latest possible operating system. Please test the Modbus Serial interface version 4.0.7.61 with operating systems such as Windows 10 or 11. Or release a new Modbus Serial interface th...

Rachel Morgenroth almost 2 years ago in PI Interfaces / PI Interfaces for Modbus 0 No status

2 VOTE

UniInt Interface to support Kerberos when connecting to network drive for failover file

My ops team tells me that our UniInt-based interfaces (e.g. PItoPI, PerfMon, OPC DA) authenticate to network drives (when reading/writing failover files) using NTLM. I'm told Kerberos is much more secure than NTLM and they would like to see that b...

taterhead247 almost 2 years ago in PI Interfaces / PI Interface for OPC DA 0 No status

1 VOTE

Flag Abandoned Batches

To create a separate log for abandoned batches within the interface or flag them on Asset framework that these are abandoned batch for users to recognise.

Navanita about 2 years ago in PI Interfaces / Batch Interfaces 0 No status

12 VOTE

RDBMS Interface version that support the failovertime > 20s (UFO_Interval)

If you have a query that lasts longer than 40s and a phase2 failover configuration is used. The interfaces switch constantly from primary to secondary and viceversa. With the parameter "UFO interval" you can control this behavior. However, this pa...

MiguelPalomo about 2 years ago in PI Interfaces / PI Interface for RDBMS 1 Declined

3 VOTE

Enhance AutoPoint Sync APS to sychronize point sets larger than 100,000 points

https://customers.osisoft.com/s/knowledgearticle?knowledgeArticleUrl=KB01426 PI AutoPoint Sync is a 32-bit application an can only synchronize 100,000 points in a point source. Recommend to develop the application to use a 64-bit architecture to h...

Luke Peters about 2 years ago in PI Interfaces / Other Interfaces 0 No status

1 VOTE

Interface for Modbus output to 4byte (32bit) registers

There are Modus supporting devices that feature 32bit single registers (e.g ROC800-Series). PI Interface for Modbus should be updated to have support to output to these 4byte (32bit) registers. Currently PI Interface for Modbus only has support f...

Guest about 2 years ago in PI Interfaces / PI Interfaces for Modbus 2 No status

1 VOTE

PI Interface for OPC DA and VT_ARRAY|VT_BSTR datatype

PI Interface for OPC DA has a plugin called "Time Array" to manage numerical arrays but string arrays are not supported. It would be a good improvement to develop this feature for string arrays.

Guest about 2 years ago in PI Interfaces / PI Interface for OPC DA 0 No status

9 VOTE

Support multiple Modbus devices on the same machine

Add support for multiple Modbus devices (using the same IP address but different port numbers) on the same machine. For example, the interface could allow the user to configure something like this: /dn= xxx.xx.xxx.xx:43120,/cn=1,/polldelay=0,/to...

Guest about 2 years ago in PI Interfaces / PI Interfaces for Modbus 3 Declined

0 VOTE

Support Modbus device failover

Enhance the interface to support redundant Modbus devices with different network cards/IP addresses. The controllers would publish a status update on the active device, and the interface should request data from it accordingly.

Guest about 2 years ago in PI Interfaces / PI Interfaces for Modbus 0 Declined

1 VOTE

New start-up parameter /SYNC_TIME defining a floating-window during which the interface will keep a RDB table in sync with PI data archive

The new RDBMSPI param: /SYNC_TIME=rel_start_time,rel_end_time for instance /SYNC_TIME=*-6h,*+1h When set, the interface: - after each execution of a query, which shall have the same "floating" window in its WHERE clause; for insta...

Guest about 2 years ago in PI Interfaces / PI Interface for RDBMS 1 No status

Please enter your email address

FILTER BY CATEGORY