PI Connectors

Showing 383 of 4893

Install and configure more than one PI System Connector instance per server

At local industrial sites, we deploy use cases different in nature and end user consumption in separated AF DBs, like OEE, PSM, Autoclave, utilities, etc. We need to centralize these individually into our central PI System. We need to segregate th...

Christian Leroux almost 2 years ago in PI Connectors / PI System Connector 0 No status

4 VOTE

Connector level failover - PI System Connector

Support connector-level failover in PI System Connector. Similar to UniInt failover (interfaces). Failover options should support hot, warm and cold failover.

GaryYegiazaryan 7 months ago in PI Connectors / PI System Connector 1 No status

14 VOTE

New function for Ethernet/IP (“scanner”)

Add the function to able to act as (“scanner”). At this moment the connect can only act as an adapter, that means that It can't collect data from other device that also are connector is an adapter. https://www.odva.org/Technology-Standards/EtherNe...

Guest about 2 years ago in PI Connectors / PI Connector for Ethernet/IP 0 No status

14 VOTE

PI Connector for IEC 60870-5-104: to filter IOAs

Considering the following scenario encountered by the customer: In IEC-104 data source, there might be 500 signals of single point (type=1, M_SP_NA_1) and 1000 measurements of normalized value (type=9, M_ME_NA_1); however the customer would not l...

Guest about 2 years ago in PI Connectors / Other specific PI Connector 3 No status

14 VOTE

Warm and cold PI Connector for OPC UA failover

Currently only hot failover is featured for the PI Connector for OPC UA but this creates a lot of strain on the data sources. We need to be able to select warm/cold failover mechanism.

Guest about 2 years ago in PI Connectors / PI Connector for OPC UA 0 No status

14 VOTE

Create/Write to Child Attributes

I would like to be able to write to Child attributes with the UFL connector using the StoreInElement function. Currently, it seems that the Connector cannot write to or create an attribute with a path like: ..\Element|ParentAttribute|ChildAttribu...

Guest about 2 years ago in PI Connectors / PI Connector for UFL 0 No status

14 VOTE

PI UFL Connector Event Frame Generator enhancement and bugfixes

Currently it is not possible to create an event frame from the PI UFL Connector linked to an existing element, despite the documentation does not specifically mention this restriction, you can only link the new event frame to an element created wi...

Andy about 2 years ago in PI Connectors / PI Connector for UFL 2 No status

12 VOTE

Redundancy for PI Connector Relay

Operating in a validated pharmaceutical industry, when making use of a comprehensive data/asset centralizing approach, we require the PI Connector Relay to be redundant or highly available. We are currently in the obligation to deploy the PI Conne...

Christian Leroux almost 2 years ago in PI Connectors / Other specific PI Connector 0 No status

13 VOTE

Ability to monitor which OPC UA Connector is active in a failover pair

As a PI administrator, I need to monitor which OPC UA Connector in a failover pair is currently active. When the primary OPC UA Connector goes down, I need an email notification, and vice versa when the secondary OPC UA Connector goes down.

Guest about 2 years ago in PI Connectors / PI Connector for OPC UA 1 No status

13 VOTE

PI Connectors buffering (Tau) - provide configuration options

As a PI Administrator, I would like to be able to DISABLE or configure Tau buffering SO THAT after a network outage the flood of data doesnt overload my network switch and PI DA. My current use case doesn't require the data that may be lost during...

Guest about 2 years ago in PI Connectors / General 0 No status

Please enter your email address

FILTER BY CATEGORY